RDM6300 - Revision history

62.173.173.193 at 15:16, 19 August 2022

2022-08-19T15:16:58Z

2022-08-19T15:16:19Z

2021-12-18T15:58:43Z

2021-12-18T15:57:44Z

2021-12-18T15:57:04Z

2021-11-14T17:55:18Z

2021-11-14T17:54:52Z

2020-04-20T19:59:19Z

2020-04-20T19:57:51Z

2020-04-20T19:53:29Z

Test

@@ Line 23: / Line 23: @@
   ./comtest -d /dev/ttyS1 -s 9600
-Note 2: the "Puttana Madonna" of comtest must be killed from another tty, there is no way to close it.
+Note 2: comtest must be killed from another tty, there is no way to close it.
 If you put an RFID near to the antenna, you should see its ID repeated on the console until it's near the antenna (about 1cm).

← Older revision		Revision as of 15:16, 19 August 2022
Line 34:		Line 34:
	Parity none		Parity none
	Flow controlo XON/XOFF		Flow controlo XON/XOFF
		+
		+	In node:
		+
		+	const SerialPort = require('serialport').SerialPort;
		+	const sp = new SerialPort({path: "/dev/ttyAMA2", baudRate: 9600});
		+
		+	var reading = true;
		+
		+	sp.on("open", function() {
		+	console.log("port has opened");
		+	});
		+
		+	sp.on('data', function(data){
		+	if (reading == true) {
		+	var enc = new TextDecoder();
		+	var arr = new Uint8Array(data);
		+	ready = enc.decode(arr)
		+	console.log('Data received: ', ready);
		+	reading = false;
		+	setTimeout(function() {
		+	reading = true;
		+	}, 1000);
		+	}
		+	});

← Older revision		Revision as of 15:58, 18 December 2021
Line 22:		Line 22:

	./comtest -d /dev/ttyS1 -s 9600		./comtest -d /dev/ttyS1 -s 9600
		+
		+	Note 2: the "Puttana Madonna" of comtest must be killed from another tty, there is no way to close it.

	If you put an RFID near to the antenna, you should see its ID repeated on the console until it's near the antenna (about 1cm).		If you put an RFID near to the antenna, you should see its ID repeated on the console until it's near the antenna (about 1cm).

@@ Line 7: / Line 7: @@
 You can connect pins 4 (VCC 5V), 6 (GND), 8 (UART1 TX) and 10 (UART1 RX) to the corresponding pins in the board (of course, TX to RX and vice versa).
-Note: the "Porco Dio" pinout should be read this way: N. 2 left corner, ethernet and USB on the bottom.
+Note: the "Porco Dio" pinout should be read this way: N. 2 left upper corner, ethernet and USB on the bottom.
 Check, using npi-config, that UART1 is enabled (npi-config -> Advanced options -> Serial -> serial1).

← Older revision		Revision as of 15:57, 18 December 2021
Line 6:		Line 6:

	You can connect pins 4 (VCC 5V), 6 (GND), 8 (UART1 TX) and 10 (UART1 RX) to the corresponding pins in the board (of course, TX to RX and vice versa).		You can connect pins 4 (VCC 5V), 6 (GND), 8 (UART1 TX) and 10 (UART1 RX) to the corresponding pins in the board (of course, TX to RX and vice versa).
		+
		+	Note: the "Porco Dio" pinout should be read this way: N. 2 left corner, ethernet and USB on the bottom.

	Check, using npi-config, that UART1 is enabled (npi-config -> Advanced options -> Serial -> serial1).		Check, using npi-config, that UART1 is enabled (npi-config -> Advanced options -> Serial -> serial1).

@@ Line 23: / Line 23: @@
 If you put an RFID near to the antenna, you should see its ID repeated on the console until it's near the antenna (about 1cm).
-Configurarion (it can be tested with an USB debug device with 5V power supply enabled):
+Configurarion (it can be tested with putty on Windows with an USB debug device with 5V power supply enabled):
   Baud 9600

← Older revision		Revision as of 17:54, 14 November 2021
Line 22:		Line 22:

	If you put an RFID near to the antenna, you should see its ID repeated on the console until it's near the antenna (about 1cm).		If you put an RFID near to the antenna, you should see its ID repeated on the console until it's near the antenna (about 1cm).
		+
		+	Configurarion (it can be tested with an USB debug device with 5V power supply enabled):
		+
		+	Baud 9600
		+	Data 8
		+	Stop 1
		+	Parity none
		+	Flow controlo XON/XOFF

← Older revision		Revision as of 19:59, 20 April 2020
Line 20:		Line 20:

	./comtest -d /dev/ttyS1 -s 9600		./comtest -d /dev/ttyS1 -s 9600
		+
		+	If you put an RFID near to the antenna, you should see its ID repeated on the console until it's near the antenna (about 1cm).

← Older revision		Revision as of 19:57, 20 April 2020
Line 6:		Line 6:

	You can connect pins 4 (VCC 5V), 6 (GND), 8 (UART1 TX) and 10 (UART1 RX) to the corresponding pins in the board (of course, TX to RX and vice versa).		You can connect pins 4 (VCC 5V), 6 (GND), 8 (UART1 TX) and 10 (UART1 RX) to the corresponding pins in the board (of course, TX to RX and vice versa).
		+
		+	Check, using npi-config, that UART1 is enabled (npi-config -> Advanced options -> Serial -> serial1).

	[[File:RFID125Headers.png]]		[[File:RFID125Headers.png]]
		+
		+	Download and compile comtest
		+
		+	git clone https://github.com/friendlyarm/comtest.git
		+	cd comtest
		+	gcc -o comtest comtest.c
		+
		+	then test it
		+
		+	./comtest -d /dev/ttyS1 -s 9600

← Older revision		Revision as of 19:53, 20 April 2020
Line 6:		Line 6:

	You can connect pins 4 (VCC 5V), 6 (GND), 8 (UART1 TX) and 10 (UART1 RX) to the corresponding pins in the board (of course, TX to RX and vice versa).		You can connect pins 4 (VCC 5V), 6 (GND), 8 (UART1 TX) and 10 (UART1 RX) to the corresponding pins in the board (of course, TX to RX and vice versa).
		+
		+	[[File:RFID125Headers.png]]