Difference between revisions of "PWM in NanoPi M4"
(Created page with "== Preparing NanoPi M4 for PWM == === Installation === Download the file rk3399-eflasher-friendlycore-bionic-4.4-arm64-20191227.img from the FriendlyElec repository. Then,...") |
(→PWM) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
== Preparing NanoPi M4 for PWM == | == Preparing NanoPi M4 for PWM == | ||
| + | |||
| + | === Wiring === | ||
| + | |||
| + | [[File:Review-NPIM4p31.jpg]] | ||
=== Installation === | === Installation === | ||
| Line 37: | Line 41: | ||
echo 0 > /sys/class/pwm/pwmchip1/export | echo 0 > /sys/class/pwm/pwmchip1/export | ||
| + | echo 100000 > /sys/class/pwm/pwmchip1/pwm0/period | ||
echo normal > /sys/class/pwm/pwmchip1/pwm0/polarity | echo normal > /sys/class/pwm/pwmchip1/pwm0/polarity | ||
| − | |||
echo 5000 > /sys/class/pwm/pwmchip1/pwm0/duty_cycle | echo 5000 > /sys/class/pwm/pwmchip1/pwm0/duty_cycle | ||
| − | echo 1 /sys/class/pwm/pwmchip1/pwm0/enable | + | echo 1 > /sys/class/pwm/pwmchip1/pwm0/enable |
It's possible to test it connecting the PINS 19 (Ground) and 23 (PWM1) of the 24-Pins secondary header to a simple handheld oscilliscope. It will show a PWM signal of about 2V. | It's possible to test it connecting the PINS 19 (Ground) and 23 (PWM1) of the 24-Pins secondary header to a simple handheld oscilliscope. It will show a PWM signal of about 2V. | ||
| + | |||
| + | === Sowtware PWM === | ||
| + | |||
| + | Create the followinf file: | ||
| + | |||
| + | #include <errno.h> | ||
| + | #include <fcntl.h> | ||
| + | #include <stdio.h> | ||
| + | #include <stdlib.h> | ||
| + | #include <sys/stat.h> | ||
| + | #include <sys/types.h> | ||
| + | #include <unistd.h> | ||
| + | |||
| + | int main() { | ||
| + | int fd = open("/sys/class/gpio/gpio9/value", O_WRONLY); | ||
| + | if (fd == -1) { | ||
| + | perror("Unable to open /sys/class/gpio/gpio9/value"); | ||
| + | exit(1); | ||
| + | } | ||
| + | for (int i = 0; i < 10000; i++) { | ||
| + | if (write(fd, "1", 1) != 1) { | ||
| + | perror("Error writing to /sys/class/gpio/gpio9/value"); | ||
| + | exit(1); | ||
| + | } | ||
| + | usleep(400); | ||
| + | if (write(fd, "0", 1) != 1) { | ||
| + | perror("Error writing to /sys/class/gpio/gpio9/value"); | ||
| + | exit(1); | ||
| + | } | ||
| + | usleep(3600); | ||
| + | } | ||
| + | close(fd); | ||
| + | } | ||
| + | |||
| + | And compile it | ||
| + | |||
| + | gcc -o pwm9 pwm.c | ||
| + | |||
| + | Launch and test | ||
| + | |||
| + | ./pwm9 | ||
Latest revision as of 16:59, 3 April 2020
Contents
Preparing NanoPi M4 for PWM[edit]
Wiring[edit]
Installation[edit]
Download the file
rk3399-eflasher-friendlycore-bionic-4.4-arm64-20191227.img
from the FriendlyElec repository.
Then, install it in a 16GB flash memory through balenaEtcher or equivalent software.
You need to connect USB Keyboard and Mouse, and an HDMI monitor. Select the OS and click on Install.
The OS will be installed in the eMMC card (it's not included in the board, so it's necessary to buy as option).
Test[edit]
Connect the USB2Serial to the 4pins between the USB ports. It's necessary to cut a slice because it doesn't fit properly. The black wire is the most external.
Configuration:
1500000 Baud 8 Data bits 1 Stop bit Parity None Flow Control XON/XOFF
Username root, password fa .
PWM[edit]
Stop and disable the pwm-fan service
service pwm-fan stop systemctl disable pwm-fan
Then, start the PWM
echo 0 > /sys/class/pwm/pwmchip1/export echo 100000 > /sys/class/pwm/pwmchip1/pwm0/period echo normal > /sys/class/pwm/pwmchip1/pwm0/polarity echo 5000 > /sys/class/pwm/pwmchip1/pwm0/duty_cycle echo 1 > /sys/class/pwm/pwmchip1/pwm0/enable
It's possible to test it connecting the PINS 19 (Ground) and 23 (PWM1) of the 24-Pins secondary header to a simple handheld oscilliscope. It will show a PWM signal of about 2V.
Sowtware PWM[edit]
Create the followinf file:
#include <errno.h>
#include <fcntl.h>
#include <stdio.h>
#include <stdlib.h>
#include <sys/stat.h>
#include <sys/types.h>
#include <unistd.h>
int main() {
int fd = open("/sys/class/gpio/gpio9/value", O_WRONLY);
if (fd == -1) {
perror("Unable to open /sys/class/gpio/gpio9/value");
exit(1);
}
for (int i = 0; i < 10000; i++) {
if (write(fd, "1", 1) != 1) {
perror("Error writing to /sys/class/gpio/gpio9/value");
exit(1);
}
usleep(400);
if (write(fd, "0", 1) != 1) {
perror("Error writing to /sys/class/gpio/gpio9/value");
exit(1);
}
usleep(3600);
}
close(fd);
}
And compile it
gcc -o pwm9 pwm.c
Launch and test
./pwm9
